IEEE: Institute of Electrical and Electronics Engineers

IEEE, the Institute of Electrical and Electronics Engineers, is a nonprofit organization that develops and publishes over 900 standards relating to electronics, a broad field in today's modern world. Headquartered in New York City, United States, IEEE has over 400,000 members in over 160 countries. A journal publisher in addition to publishing IEEE standards, IEEE is by far the most cited publisher for new patents. Standards from IEEE are available both individually, directly through the ANSI webstore, and as part of a Standards Subscription. If you or your organization are interested in easy, managed, online access to standards that can be shared, a Standards Subscription may be what you need - please contact us at: [email protected] or 1-212-642-4980 or Request Proposal Price.

Below are IEEE's best-selling standards. To find additional standards, please use the search bar above.

IEEE/ANSI C63.27-2017

American National Standard for Evaluation of Wireless Coexistence

An evaluation process and supporting test methods are provided in this standard to quantify the ability of a wireless device to coexist with other wireless services in its intended radio frequency (RF) environments.

IEEE/ANSI C63.10-2020

American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices

Revision Standard - Active. The procedures for testing the compliance of a wide variety of unlicensed wireless transmitters (also called intentional radiators and license-exempt transmitters) including, but not limited to, remote control and security unlicensed wireless devices, frequency hopping and direct sequence spread spectrum devices, antipilferage devices, cordless telephones, medical unlicensed wireless devices, Unlicensed National Information Infrastructure (U-NII) devices, intrusion detectors, unlicensed wireless devices operating on frequencies below 30 MHz, automatic vehicle identification systems, and other unlicensed wireless devices authorized by a radio regulatory authority are covered in this standard. Excluded by this standard are test procedures for unlicensed wireless devices already covered in other published standards (e.g., Unlicensed Personal Communication Services (UPCS) devices). 

IEEE/ANSI C63.4-2014

American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz

ANSI C63.4, conducted emission testing, conducting ground plane, digital equipment, electric field measurement, line impedance stabilization network, low-voltage electrical equipment, low-voltage electronic equipment, magnetic field measurement, normalized site attenuation, radiated emission testing, radio-noise emissions, radio-noise power, site attenuation, unintentional radiators

IEEE 1547-2018

IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with Associated Electric Power Systems Interfaces

Revision Standard - Active.The technical specifications for, and testing of, the interconnection and interoperability between utility electric power systems (EPSs) and distributed energy resources (DERs) are the focus of this standard. It provides requirements relevant to the performance, operation, testing, safety considerations, and maintenance of the interconnection. It also includes general requirements, response to abnormal conditions, power quality, islanding, and test specifications and requirements for design, production, installation evaluation, commissioning, and periodic tests. The stated requirements are universally needed for interconnection of DER, including synchronous machines, induction machines, or power inverters/converters and will be sufficient for most installations. The criteria and requirements are applicable to all DER technologies interconnected to EPSs at typical primary and/or secondary distribution voltages. Installation of DER on radial primary and secondary distribution systems is the main emphasis of this document, although installation of DERs on primary and secondary network distribution systems is considered. This standard is written considering that the DER is a 60 Hz source.

IEEE 519-2014

IEEE Recommended Practice and Requirements for Harmonic Control in Electric Power Systems

Goals for the design of electrical systems that include both linear and nonlinear loads are established in this recommended practice. The voltage and current waveforms that may exist throughout the system are described, and waveform distortion goals for the system designer are established. The interface between sources and loads is described as the point of common coupling and observance of the design goals will reduce interference between electrical equipment. This recommended practice addresses steady-state limitations. Transient conditions exceeding these limitations may be encountered. This document sets the quality of power that is to be provided at the point of common coupling. This document does not cover the effects of radio-frequency interference, however, guidance is offered for wired telephone systems.

IEEE C57.104-2019

IEEE Guide for the Interpretation of Gases Generated in Mineral Oil-Immersed Transformers

Detailed procedures for interpreting Dissolved Gas Analysis results are described in this guide. The document details: 1) Overview of gas generation in transformer and DGA process; 2) The purpose and application of DGA; 3) DGA quality verification and DGA limitations; 4) DGA interpretation and norms; 5) Fault type definitions and identification; 6) Case studies and interpretation example. The intent is to provide the operator with useful information concerning the serviceability of the equipment. An extensive bibliography on gas evolution, detection, and interpretation is included. 

IEEE C95.3-2021

IEEE Recommended Practice for Measurements and Computations of Electric, Magnetic, and Electromagnetic Fields with Respect to Human Exposure to Such Fields, 0 Hz to 300 GHz

Revision Standard - Active. Best practices are described for the development, validation, and application of methods for the computation and measurement of relevant metrics characterizing human exposure to electric and/or magnetic fields (collectively, electromagnetic fields) over the frequency range of 0 Hz to 300 GHz. This recommended practice is a replacement for IEEE Std C95.3™-2002 and IEEE Std C95.3.1™-2010, extensively revising the contents from those and harmonizing with IEEE Std C95.1™-2019. Detailed methodology is not described; rather, requirements for best practice are expressed through guidance and references to other documents and standards. Examples are included to clarify the guidance. This recommended practice is intended for professional users who are familiar with basic electromagnetic field theory and practice and for persons involved in specifying or implementing critical hazard assessments or surveys such as those described in IEEE Std C95.7™-2014. (The PDF of this standard is available in the IEEE GET program at no cost to you compliments of the United States Navy, United States Air Force, and United States Army https://ieeexplore.ieee.org/browse/standards/get-program/page/series?id=82) 

IEEE 1547.1-2020

IEEE Standard Conformance Test Procedures for Equipment Interconnecting Distributed Energy Resources with Electric Power Systems and Associated Interfaces

This standard specifies the type, production, commissioning, and periodic tests and evaluations that shall be performed to confirm that the interconnection and interoperation functions of equipment and systems interconnecting distributed energy resources (DERs) with the electric power system (EPS) conform to IEEE Std 1547, as revised, corrected, or amended.

IEEE/ANSI C63.4a-2017

American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Amendment 1: Test Site Validation

Amendment Standard - Active.U.S. consensus standard methods are specified in Annex D of this amendment for validating standard test sites and alternative test sites used for measurement of radiated radio-frequency (RF) signals and noise emitted from electrical and electronic devices in the frequency range of 30 MHz to 1 GHz. In addition, various updates are made to equations in 4.5, Annex F, Annex G, and Annex N.

IEEE 524-2016

IEEE Guide for the Installation of Overhead Transmission Line Conductors

General recommendations for the selection of methods, equipment, and tools that have been found to be practical for the stringing of overhead transmission line conductors and overhead groundwires are provided.